Hydraulic Seals

are available as rod seals and piston seals, with pressurisation on one or both sides, as well as wipers for hydraulic applications, guides and bearing elements.

Hydraulic Seals

Hydraulic seals are used in hydraulic systems. As rod seals, they serve to seal moving cylinder rods against the medium escaping to the outside. Piston seals separate the two cylinder chambers from each other.

A distinction is made between single-action and double-action sealing elements. Double-action seals are used when pressure is applied on both sides. They simplify the housing as they save a groove on the piston.

Skip navigation

Gleitdichtungssatz 1G9

Slide Seal Set 1G9

Slide seal set for general machine-building, machine tools and mobile hydraulic applications. Depending on PTFE compound and elastomer, adaptable to many media and operating conditions. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Pressure: ≤ 400 bar
Temperature: -30 °C / +100 °C
Sliding Speed: ≤ 4 m/s
Standard Material: 0005X

Lippenring 1H0

Lip Seal 1H0

Lip seal for standard hydraulic and pneumatic applications. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Hydraulic:
Pressure: ≤ 160 bar
Temperature: -35 °C / +100 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: NBR
Pneumatic:
Pressure: ≤ 16 bar
Temperature: -35 °C / +80 °C
Sliding Speed: ≤ 1 m/s
Standard Material: NBR

Lippenring 1H1

Lip Seal 1H1

Lip seal with increased wear and pressure resistance, for tough operating conditions in hydraulic applications. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Pressure: ≤ 400 bar
Temperature HFA-, HFB-, HFC-liquids: ≤ +40 °C
Temperature mineral oils: -35 °C / +105 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: PUR

Lippenring 1H2

Lip Seal 1H2

Lip seal like 1H1, but with 2 sealing lips for retention of a lubrication pocket and for better sealing effect in depressurised state. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Pressure: ≤ 400 bar
Temperature HFA-, HFB-, HFC-liquids: ≤ +40 °C
Temperature mineral oils: -35 °C / +105 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: PUR

Kompakter Lippenring 1H3

Compact Lip Seal 1H3

Compact lip seal for small fitting areas in hydraulic applications. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Pressure: ≤ 400 bar
Temperature HFA-, HFB-, HFC-liquids: ≤ +40 °C
Temperature mineral oils: -35 °C / +105 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: PUR

PUR-Lippenring 1H4

Lip Seal 1H4

Lip seal with 2 sealing lips, O-ring and back-up ring for the toughest operating conditions in hydraulic applications. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 500 bar (≤ 1000 bar peak pressure)
Temperature (mineral oils: -35 °C / +110 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: PUR/PA, NBR

Kompakter Lippenring 1HL

Compact Lip Seal 1HL

Compact lip seal for small fitting areas in hydraulic applications. Optimised for especially low friction. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 250 bar
Temperature: -35 °C / +110 °C
Sliding Speed: ≤ 1 m/s
Standard Material: PUR

Lippenring 1HS

Lip Seal 1HS

Lip seal for hydraulic and pneumatic applications. Especially suitable for use in gas springs. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure Hyraulics/Gas Springs: ≤ 200 bar
Pressure Rotating Unions: ≤ 20 bar
Temperature: -35 °C / +90 °C
Sliding Speed Hydraulics/Gas Springs: ≤ 1 m/s
Sliding Speed Rotating Unions: ≤ 0,2 m/s
Standard Material: PUR

Kompakt-Stangendichtung 1HK

Compact Rod Seal 1HK

PUR compact rod seal with integrated anti-extrusion ring. A typical application is as a buffer seal in sealing systems. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 500 bar (≤ 1000 bar peak pressure)
Temperature: -35 °C / +110 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: PUR

Kompaktdichtung 1H6

Compact Seal 1H6

Fabric compact seal for medium-duty hydraulic applications. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 250 bar
Temperature: -30 °C / +100 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: 0001K

Kompaktdichtung 1H8

Compact Seal 1H8

Fabric compact seal with back-up ring against gap extrusion, for medium-duty hydraulic applications. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 250 bar
Temperature: -30 °C / +100 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: 0001K

Kompaktdichtung 1H9

Compact Seal 1H9

Compact seal with back-up ring, good sealing effect also at low pressures. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 315 bar
Temperature: -30 °C / +100 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: 0030N

Kompaktdichtung 1HC

Compact Seal 1HC

Compact seal with back-up ring for fitting areas according to ISO 7425-2. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 315 bar
Temperature: -30 °C / +100 °C
Sliding Speed: ≤ 1 m/s
Standard Material: NBR/PTFE-Compound

Gewebe-Dachmanschettensatz MA0

Fabric Chevron Sealing MA0

Fabric chevron sealing set for complicated and not exactly definable operating conditions in hydraulic applications. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 500 bar
Temperature: -40 °C / +100 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: NBR/fabric

Gewebe-Dachmanschettensatz MA2

Fabric Chevron Sealing MA2

Fabric chevron sealing set for complicated operating conditions, standard series for pressures up to 350 bar in hydraulic applications. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 350 bar
Temperature: -40 °C / +100 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: NBR/fabric

Gewebe-Dachmanschettensatz MA3

Fabric Chevron Sealing MA3

Fabric chevron sealing set for difficult operating conditions, standard series for pressures up to 500 bar in hydraulic applications. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 500 bar
Temperature: -40 °C / +100 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: NBR/fabric

PUR-Lippenring mit O-Ring 3H2

PUR Lip Seal 3H2

PUR lip seal with O-ring, to achieve good sealing even at low pressures. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 350 bar
Temperature: -35 °C / +80 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: PUR/NBR

Gleitdichtungssatz 1G0

Slide Seal Set 1G0

Slide seal set for light-duty hydraulic and pneumatic applications. Depending on PTFE compound and elastomer, adaptable to many media and operating conditions. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Pressure: ≤ 160 bar (hyd.) / ≤ 16 bar (pneu.)
Temperature: -30 °C / +100 °C (Standard)
Temperatur: -60 °C / +200 °C (Depending on O-ring material selected)
Sliding Speed: ≤ 4 m/s
Standard Material: 0006X

Gleitdichtungssatz 1G2

Slide Seal Set 1G2

Slide seal set for general machine-building, machine tools and mobile hydraulic applications. Depending on PTFE compound and elastomer, adaptable to many media and operating conditions. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Pressure: ≤ 400 bar
Temperature: -30 °C / +100 °C
Sliding Speed: ≤ 4 m/s
Standard Material: 0005X

Gleitdichtungssatz 1G4

Slide Seal Set 1G4

Slide seal set for O-ring fitting areas according to ASA 568 A. Depending on PTFE compound and elastomer, adaptable to many media and operating conditions. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Pressure: ≤ 350 bar
Temperature: -30 °C / +100 °C
Sliding Speed: ≤ 4 m/s
Standard Material: 0045X

Gleitdichtungssatz 1GT

Slide Seal Set 1GT

Slide seal set for general machine-building, machine tools and mobile hydraulic applications. Depending on PTFE compound and elastomer, adaptable to many media and operating conditions. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Pressure: ≤ 400 bar
Temperature: -30 °C / +100 °C
Sliding Speed: ≤ 4 m/s
Standard Material: 0005X

Lippenring 2H0

Lip Seal 2H0

Lip seal for standard hydraulic and pneumatic applications. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Hydraulics:
Pressure: ≤ 160 bar
Temperature: -25 °C / +100 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: NBR
Pneumatics:
Pressure: ≤ 16 bar
Temperature: -25 °C / +80 °C
Sliding Speed: ≤ 1 m/s
Standard Material: NBR

Gleitdichtungssatz 2G9

Glide Seal Set 2G9

Glide seal set for general machine-building, machine tools and mobile hydraulic applications. Depending on PTFE compound and elastomer, adaptable to many media and operating conditions. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Pressure: ≤ 400 bar
Temperature: -30 °C / +100 °C
Sliding Speed: ≤ 4 m/s
Standard Material: 0005X

Lippenring 2H1

Lip Seal 2H1

Lip seal with increased wear and pressure resistance for hydraulic applications. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Pressure: ≤ 400 bar
Temperature HFA-, HFB-, HFC-liquids: ≤ +40 °C
Temperature mineral oils: -35 °C / +105 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: PUR

Kompaktdichtung 2H2

Compact Seal 2H2

Compact seal for heavy-duty hydraulic applications, only for divided pistons. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 500 bar
Temperature: -40 °C / +100 °C
Sliding Speed: ≤ 1 m/s
Standard Material: 0001K

Nutring mit Stützring 2H3

Lip Seal 2H3

Lip seal with back-up ring for medium-duty hydraulic applications, only for divided pistons. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 250 bar
Temperature: -40 °C / +100 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: NBR/fabric

Nutring 3H1

Symmetrical Lip Seal 3H1

Symmetrical lip seal. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 400 bar
Temperature: -30 °C / +80 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: PUR

PUR-Lippenring mit O-Ring 3H2

PUR Lip Seal 3H2

PUR lip seal with O-ring, to achieve good sealing even at low pressures. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 350 bar
Temperature: -35 °C / +80 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: PUR/NBR

Gewebe-Dachmanschettensatz MA4

Fabric Chevron Sealing MA4

Fabric chevron sealing set for heavy-duty hydraulic applications. Only for divided pistons. Do not fit with axial compression. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 500 bar
Temperature: -40 °C / +100 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: NBR/fabric

Gewebe-Dachmanschettensatz MB0

Fabric Chevron Sealing Set MB0

Fabric chevron sealing set with radial pretension for heavy-duty hydraulic applications. Only for divided pistons. Do not fit with axial compression. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 500 bar
Temperature: -40 °C / +100 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: NBR/fabric

Gleitdichtungssatz 2G0

Glide Seal Set 2G0

Glide seal set for light-duty hydraulic and pneumatic applications. Depending on PTFE compound and elastomer, adaptable to many media and operating conditions. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Pressure pneumatics: ≤ 16 bar
Pressure hydraulics: ≤ 160 bar
Temperature: -30 °C / +100 °C (Standard)
Temperatur: -60 °C / +200 °C (Depending on O-ring material selected)
Sliding Speed: ≤ 4 m/s
Standard Material: 0006X

Gleitdichtungssatz 2G2

Glide Seal Set 2G2

Glide seal set for general machine-building, machine tools and mobile hydraulic applications. Depending on PTFE compound and elastomer, adaptable to many media and operating conditions. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Pressure: ≤ 400 bar
Temperature: -30 °C / +100 °C
Sliding Speed: ≤ 4 m/s
Standard Material: 0005X

Gleitdichtungssatz 2GT

Glide Seal Set 2GT

Glide seal set for general machine-building, machine tools and mobile hydraulic applications. Depending on PTFE compound and elastomer, adaptable to many media and operating conditions. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Pressure: ≤ 400 bar
Temperature: -30 °C / +100 °C
Sliding Speed: ≤ 4 m/s
Standard Material: 0005X

Kolben-Dichtungssatz 2G3

Piston Seal Set 2G3

Special glide seal set with divided slide ring (stepped cut) for heavy-duty hydraulic applications. Very simple fitting. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 800 bar
Temperature: -30 °C / +110 °C
Sliding Speed: ≤ 1 m/s
Standard Material: 0175X

Gleitdichtungssatz 2G4

Glide Seal Set 2G4

Glide seal set for O-ring fitting areas according to ASA 568 A. Depending on PTFE compound and elastomer, adaptable to many media and operating conditions. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Pressure: ≤ 350 bar
Temperature: -30 °C / +100 °C
Sliding Speed: ≤ 4 m/s
Standard Material: 0045X

Gleitdichtungssatz 2G5

Glide Seal Set 2G5

Glide geal set for heavy-duty hydraulic applications, only for divided pistons. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Pressure: ≤ 500 bar
Temperature: -30 °C / +100 °C
Sliding Speed: ≤ 4 m/s
Standard Material: 0006X

Kolben-Dichtungssatz 2G6

Piston Seal Set 2G6

Piston seal set for light to medium-duty hydraulic applications. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 300 bar
Temperature: -35 °C / +110 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: 0013X

Mehrteilige Kompaktdichtung 2H6

Multi-Part Compact Seal 2H6

Multi-part compact seal with increased wear resistance for medium to heavy-duty hydraulic applications, for closed grooves in standard hydraulic cylinders. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 400 bar
Temperature: -30 °C / +100 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: PUR

Mehrteilige Kompaktdichtung 2H8

Multi-Part Compact Seal 2H8

Multi-part compact seal for medium to heavy-duty hydraulic applications, for closed grooves in standard hydraulic cylinders. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 350 bar
Temperature HFA-, HFB-, HFC-liquids: ≤ +40 °C
Temperature mineral oils: -30 °C / +100 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: 0080N

Kolbendichtringe 2HD

Piston Seal 2HD

Piston Seal for small fitting areas, interchangeable with, for example, X-rings. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure (stat.): ≤ 600 bar
Pressure (dyn.): ≤ 250 bar
Temperature HFA-, HFB-, HFC-liquids: ≤ +40 °C
Temperature mineral oils: -30 °C / +100 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: PUR

Komplettkolben 2T2

Complete Piston 2T2

Complete piston, spring-supported, for pneumatic applications (in simple constructions also for low-pressure hydraulic applications). Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Pressure: ≤ 10 bar (≤ 40 bar in Hydraulic Applications)
Temperature: -20 °C / +100 °C
Sliding Speed: ≤ 0,5 m/s
Standard Material: NBR/steel core

Abstreifer 1A1

Wiper 1A1

Wiper with flush housing end, snap fit. The wiper 1A1 is universally applicable and particularly suitable for applications in which a flush housing end is tobe achieved. Depending on profile width and diameter, snapfit in closed and undercut housings is possible. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers). Snap fit is dependent on the profile width and diameter in the case of the materials POM, PA and PE. Also available in special sizes at short notice from current production.

Application Range

Temperature NBR: -35 °C / +100 °C
Temperature PUR - Hydraulic Oils (Mineral Oil Basis): -35 °C /+100 °C
Temperature PUR - Water, Emulsions ≤ 50 °C
Sliding Speed: ≤ 2 m/s
Standard Materials: NBR, PUR

Abstreifer 1A5

Wiper 1A5

The wiper 1A5 is universally applicable and suitable for all applications in general mechanical engineering. Depending on profile width and diameter, snap fit in closed and undercut housings is possible. Pressurisation against the back of the wiper should be prevented. In the PUR version, the wiper 1A5 is particularly suitable where increased wear resistance is required. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers). Snap fit is dependent on the profile width and diameter in the case of the materials POM, PA and PE. Also available in special sizes at short notice from current production.

Application Range

Temperature NBR: -30 °C / +100 °C
Temperature PUR - Hydraulic Oils (Mineral Oil Basis): -35 °C /+100 °C
Temperature PUR - Water, Emulsions ≤ 50 °C
Sliding Speed NBR: ≤ 2 m/s
Sliding Speed PUR: ≤ 1 m/s
Standard Material: NBR, PUR

Abstreifer 1AM

Wiper 1AM

The wiper 1AM is universally applicable in almost all applications of general mechanical engineering. Due to its metal cage that is firmly attached to the elastomer part, it is particularly suitable for applications where a tight fit in an open housing is required. For use in particularly wear-intensive applications or in applications with increased UV or ozone exposure, the wiper is available in PUR. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature Hydraulics NBR: -35 °C / +100 °C
Temperature Hydraulics PUR - Hydraulic Oils (Mineral Oil Basis): -35 °C / +100 °C
Temperature Hydraulics PUR - Water, Emulsions ≤ 50 °C
Temperature Pneumatics PUR: -35 °C / +80 °C
Sliding Speed: ≤ 2 m/s

Doppelabstreifer 1AZ

Double Wiper 1AZ

The elastomer wiper 1AZ is universally applicable in almost all applications in which a particularly good wiping effect to the outside and inside aswell as a reduction of the residual oil film is required. Depending on profile width and diameter, snap fit in closed and undercut housings is possible. The wiper 1AZ is mainly used with sealing elements which have a universal hydrodynamic backpumping capability.

Design: The double wiper has two elastic lips. One acts as a wiper lip and one as a sealing lip. The sealing lip reduces the residual oil film by wiping it inwards. Depending on the application, the double wiper can be made of NBR or PUR.

Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature NBR: -30 °C / +110 °C
Sliding Speed NBR: ≤ 1,0 m/s
Temperature PUR: -35 °C / +100 °C
Sliding Speed PUR: ≤ 0,8 m/s

Doppelabstreifer 1AY

Double Wiper 1AY

The PUR wiper 1AY is universallyapplicable in almost all appli-cations in which a particularlygood wiping effect to the out-side and inside as well as areduction of the residual oil filmis required. Depending on profilewidth and diameter, snap fitin closed and undercut housings is possible.

Design: The double wiper has two elastic lips. One acts as a wiper lip and one as a sealing lip. The sealing lip also reduces the residual oil film by wiping it inwards.

Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature Hydraulics - Hydraulic Oils (Mineral Oil Basis): -35 °C / +100 °C
Temperature Hydraulics - Water, Emulsions: ≤ 50 °C
Temperature Pneumatics: -35 °C / +80 °C
Sliding Speed: ≤ 2 m/s
Standard Material: PUR

Doppelabstreifer 1AV

Double action wiper 1AV

Double wiper with dirt shield and pressure relief drill hole. Particularly suitable for applications in mobile hydraulics.

Design: The double wiper has two elastic lips made of PUR, one of which acts as a wiper lip and one as a sealing lip. The sealing lip reduces the residual oil film by wiping it inwards. An additional dirt shield prevents the penetration of dirt and moisture, especially on vertical cylinder rods. It also has a pressure relief hole, which prevents a pressure build up between the wiper lip and the sealing-/wiper lips.

Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature: -35 °C / +100 °C
Sliding Speed: ≤ 2 m/s
Standard Material: PUR

Abstreifer 1A8

Wiper 1A8

The wiper 1A8 is particularly suitable for applications in which stubborn adhering dirt, ice and sludge must be reliably wiped off. Due to its metal cage that is firmly attached to bothlips - the elastomer part and scraper lip made of brass - it is particularly suitable for applications where a tight fit in an open housing is required.

Design: The scraper has two different scraper lips. A thin wiper lip made of brass and an elastic lip made of NBR. The metallic wiperlip has the task of removing firmly adhering impurities and ice particles. The secondary lip made of elastomer material has a supporting effect by reliably wiping off water, sand particles and similar foreign substances. Both lips are arranged in tandem one after another in a compact metal housing.

Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature: -40 °C / +100 °C
Sliding Speed: ≤ 1 m/s
Standard Material: NBR

Abstreifer 1AF

Wiper 1AF

Thanks to its robust profile the PUR wiper 1AF is suitable for the toughest conditions in wear-intensive applications. Due to its metal cage that is firmly attached to the elastomer part, it is particularly suitable for applications where a tight fit in an open housing is required.

Design: The wiper consists of a PUR wiper ring and a metal cage firmly connected to it.

Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature: -35 °C / +100 °C
Sliding Speed: ≤ 2 m/s
Standard Material: PUR

Abstreifer 1AG

Wiper 1AG

Thanks to its robust profile the PUR wiper 1AG is suitable for the toughest conditions in wear-intensive applications. Due to its metal cage that is firmly attached to the elastomer part, it is particularly suitable for applications where a tight fit in an open housing is required.

Design: The wiper consists of a PUR wiper ring and a metal cage firmly connected to it.

Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature: -35 °C / +100 °C
Sliding Speed: ≤ 2 m/s
Standard Material: PUR

Abstreifer 1AP

Wiper 1AP

The wiper 1AP is universally applicable and particularly suitable for applications where a tight fit in an open housing and protection of the housing against possible damage during installation and removal of the wiper is required. In the PUR version, the wiper 1AP is particularly wear-resistant.

Design: The wiper consists of a elastomere wiper ring and a metal cage firmly connected to it, which is covered with elastomere.

Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature Hydraulics: -35 °C / +100 °C
Temperature Pneumatics: -35 °C / +80 °C
Sliding Speed: ≤ 2 m/s
Standard Materials: NBR, PUR

Doppelabstreifer 1AQ

Double Wiper 1AQ

The wiper 1AQ is particularly suitable for applications in which a flush housing end is to be achieved and a particularly good wiping effect to the outside and inside as well as a reduction of the residual oilfilm is required. It is also suitable for applications where a tight fit in an open housing and protection of the metal cage against corrosion is required.

Design: The double wiper consists of a NBR wiper ring and a metal cage which is firmly connected to it and which is completely encased in NBR. It has two elastic lips of which one acts as a wiper lip and one as a sealing lip. The sealing lip also reduces the residual oil film by wiping it inwards.

Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature Hydraulics: -30 °C / +100 °C
Temperature Pneumatics: -35 °C / +80 °C
Sliding Speed: ≤ 2 m/s
Standard Material: NBR

Doppelabstreifer 1AH

Double Wiper 1AH

The double wiper 1AH is suitable for the toughest conditions in which a particularly good wiping effect to the outside and inside as well as a reduction of the residual oil film is required. Due to its metal cage that is firmly attached to the elastomer part, it is particularly suitable for applications where a tight fit in an open housing is required. In the PUR version, it is suitable for wear-intensive applications.

Design: The double wiper 1AH is suitable for the toughest conditions in which a particularly good wiping effect to the outside and inside as well as a reduction of the residual oil film is required. Due to its metal cage that is firmly attached to the elastomer part, it is particularly suitable for applications where a tight fit in an open housing is required.

In the PUR version, the elastomer part also has a pressure relief hole, which enables pressure compensation between wiper and seal. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature NBR: -30 °C / +100 °C
Temperature PUR: -35 °C / +100 °C
Sliding Speed: ≤ 2 m/s
Standard Materials: NBR, PUR

Abstreifer 1A6

Wiper 1A6

The NBR wiper 1A6 is particularly suitable for applications in mobile hydraulics and mining where the penetration of dirt and moisture must be reliably prevented and at the same time the compensation of high radial tolerances is required. Depending on profile width and diameter, snap fit in closed and undercut housings is possible.

Application Range

Temperature: -20 °C / +100 °C
Sliding Speed: ≤ 4 m/s
Standard Material: NBR
Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Abstreifer 1A7

Wiper 1A7

The polyamide wiper 1A7 is particularly suitable for applications in which stubbornly adhering particles and dirt must be reliably wiped off. Depending on profile width and diameter, snap fit in closed and undercut housings is possible. The wiper 1A7 should always be used in conjunction with an elastomer wiper. Pressure against the back of the wiper should be prevented. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Temperature: -40 °C / +100 °C
Sliding Speed: ≤ 1 m/s
Standard Material: PA (PA-Compound)

Abstreifer 1S0

Wiper 1S0

The PTFE wiper 1S0 is particularly suitable for applications in which outstanding low friction and good resistance to high temperatures and aggressive media are required. A wide range of PTFE compounds for the sliding ring and elastomers for the prestress element makes the 1S0 wiper ideal for these applications and adaptable to a wide variety of media and operating conditions. The low breakaway/sliding friction ensures smooth movement even at low speeds. Depending on profile width and diameter, installation in closed and undercut housings is possible. Other materials are availablefor special operating conditions. Our application engineers will be glad to advise you.

Application Range

Temperature: -30 °C/+100 °C
Max. temperatures dependent on selected o-ring material: -60 °C or +200 °C
Sliding Speed: ≤ 4 m/s
Standard materials: PTFE-Compound/Elastomere

Doppelabstreifer 1S1

Double Wiper 1S1

The PTFE wiper 1S1 is particularly suitable for applications in which outstanding low friction and good resistance to high temperatures and aggressive media are required. A wide range of PTFE compounds for the sliding ring and elastomers for the prestress element makes the 1S1 wiper ideal for these applications and adaptable to a wide variety of media and operating conditions. The low breakaway/sliding friction ensures smooth movement even at low speeds. Depending on profile width and diameter, installation in closed and undercut housings is possible. Other materials are availablefor special operating conditions. Our application engineers will be glad to advise you.

Application Range

Temperature: -30 °C/+100 °C
Max. temperatures dependent on selected o-ring material: -60 °C or +200 °C
Sliding Speed: ≤ 4 m/s
Standard materials: PTFE-Compound/Elastomere

Abstreifer 1S2

Double Wiper 1S2

The PTFE wiper 1S2 is particularly suitable for applications in which outstanding low friction and good resistance to high temperatures and aggressive media are required. A wide range of PTFE compounds for the sliding ring and elastomers for the prestress element makes the 1S2 wiper ideal for these applications and adaptable to a wide variety of media and operating conditions. The low breakaway/sliding friction ensures smooth movement even at low speeds. Depending on profile width and diameter, installation in closed and undercut housings is possible. Other materials are availablefor special operating conditions. Our application engineers will be glad to advise you.

Application Range

Temperature: -30 °C/+100 °C
Max. temperatures dependent on selected o-ring material: -60 °C or +200 °C
Sliding Speed: ≤ 4 m/s
Standard materials: PTFE-Compound/Elastomere

Doppelabstreifer 1S3

Double action wiper 1S3

The PTFE wiper 1S3 is particularly suitable for applications in which outstanding low friction and good resistance to high temperatures and aggressive media are required. A wide range of PTFE compounds for the sliding ring and elastomers for the prestress element makes the 1S3 wiper ideal for these applications and adaptable to awide variety of media and operating conditions. The low breakaway/sliding friction ensures smooth movement even at low speeds. Depending on profile width and diameter, installation in closed and undercut housings is possible. There must be a pressure relief hole between sealing elements and wiper. Other materials are availablefor special operating conditions. Our application engineers will be glad to advise you.

Application Range

Temperature: -30 °C/+100 °C
Max. temperatures dependent on selected o-ring material: -60 °C or +200 °C
Sliding Speed: ≤ 4 m/s
Standard materials: PTFE-Compound/Elastomere

Führungsband FB3

Guide Strip FB3

Guide strip with very good sliding characteristics and stick-slip free run, for light to medium-duty oil hydraulics. Available also with lubrication pockets. Cut goods. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Standard Material: PTFE/carbon (0005T)
Temperature: -100 °C / +200 °C
Sliding Speed: ≤ 5 m/s

Führungsband FB2

Guide Strip FB2

Guide strip with chamfer, very good sliding characteristics and stick-slip free run, for pneumatics and light to medium-duty water hydraulics, chemical and foodstuff applications. Available also with lubrication pockets. Cut goods. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Standard Material: PTFE/carbon (0005T)
Temperature: -100 °C / +200 °C
Sliding Speed: ≤ 5 m/s

Hartgewebe-Führungsbänder FB8

Compound Fabric Guide Strips FB8

Compound fabric guide strips, wrapped (coil), perform the function of guiding pistons and piston rods in hydraulic applications. They absorb the radial forces and protect the rod and cylinder from making metallic contact. Cut goods up to 5700 mm or on custom cutting. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature: -50 °C / +120 °C
Sliding Speed: ≤ 0,8 m/s
Standard Material: T200K; T550K

Hartgewebe-Führungsbänder FB9

Compound Fabric Guide Strips FB9

Compound fabric guide strips, spiralised (helix), perfom the function of guiding pistons and piston rods in hydraulic applications. They absorb the radial forces and protect the rod and cylinder from making metallic contact. Cut goods up to 5700 mm or on custom cutting. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature: -50 °C / +120 °C
Sliding Speed: ≤ 0,8 m/s
Standard Material: T550K

Führungsringe FÜB1

Wear Rings FÜB1

Compound Fabric Wear Rings, oblique slot, are mainly used in hydraulics and machine building. They perform the function of guiding rods, prevent them from making metallic contact and absorb radial forces. In the material POM also available in special dimensions at short notice from routine production. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Temperature: -50 °C / +120 °C
Sliding Speed: ≤ 0,5/0,8 m/s (depends on the amterial selected)
Materials:
- Synthetic woven fabric with a specially modified phenolic resin impregnated and PTFE additives (2000K)
- Phenolic resin impregnated cotton fabric (1000K)
- Phenolic resin impregnated fine cotton fabric (0051K)
- Resin impregnated plastics fabric with PTFE additives (1030 - 0052K)
- Resin impregnated plastics fabric with graphite additives (0942 - 0052K)

Führungsringe FÜB2

Wear Rings FÜB2

Compound Fabric Wear Rings, oblique slot, are mainly used in hydraulics and machine building. They perform the function of guiding pistons, prevent them from making metallic contact and absorb radial forces. In the material POM also available in special dimensions at short notice from routine production. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Temperature: -50 °C / +120 °C
Sliding Speed: ≤ 0,5/0,8 m/s (depends on the amterial selected)
Materials:
- Synthetic woven fabric with a specially modified phenolic resin impregnated and PTFE additives (2000K)
- Phenolic resin impregnated cotton fabric (1000K)
- Phenolic resin impregnated fine cotton fabric (0051K)
- Resin impregnated plastics fabric with PTFE additives (1030 - 0052K)
- Resin impregnated plastics fabric with graphite additives (0942 - 0052K)

Führungsringe FÜB

Wear Rings FÜB

Wear ring,oblique slot, for rods and pistons in hydraulic, machine-building and chemical applications. In the material POM also available in special dimensions at short notice from routine production. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Temperature: -50 °C / +120 °C
Sliding Speed: ≤ 0,5/0,8 m/s (depends on the amterial selected)
Materials:
- Synthetic woven fabric with a specially modified phenolic resin impregnated and PTFE additives (2000K)
- Phenolic resin impregnated cotton fabric (1000K)
- Phenolic resin impregnated fine cotton fabric (0051K)
- Resin impregnated plastics fabric with PTFE additives (1030 - 0052K)
- Resin impregnated plastics fabric with graphite additives (0942 - 0052K)

Hartgewebe-Führungsringe FÜA1

Wear Rings FÜA1

Compound Fabric Wear Rings, straight slot, are mainly used in hydraulics and machine building. They perform the function of guiding rods, prevent them from making metallic contact and absorb radial forces. In the material POM also available in special dimensions at short notice from routine production. Application Range Temperature: -50 °C / +120 °C (depends on the material selected) Sliding Speed: <= 0,5/0,8 m/s (depends on the material selected) Materials: - Synthetic woven fabric with a specially modified phenolic resin impregnated and PTFE additives (2000K) - Phenolic resin impregnated cotton fabric (1000K) - Phenolic resin impregnated fine cotton fabric (0051K) - Resin impregnated plastics fabric with PTFE additives (1030 - 0052K) - Resin impregnated plastics fabric with graphite additives (0942 - 0052K) Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Hartgewebe-Führungsringe FÜA2

Wear Rings FÜA2

Compound Fabric Wear Rings, straight slot, are mainly used in hydraulics and machine building. They perform the function of guiding pistons, prevent them from making metallic contact and absorb radial forces. In the material POM also available in special dimensions at short notice from routine production. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Temperature: -50 °C / +120 °C
Sliding Speed: ≤ 0,5/0,8 m/s (depends on the material selected)
Materials:
- Synthetic woven fabric with a specially modified phenolic resin impregnated and PTFE additives (2000K)
- Phenolic resin impregnated cotton fabric (1000K)
- Phenolic resin impregnated fine cotton fabric (0051K)
- Resin impregnated plastics fabric with PTFE additives (1030 - 0052K)
- Resin impregnated plastics fabric with graphite additives (0942 - 0052K)

Hartgewebe-Führungsringe FÜA

Wear Rings FÜA

Compound Fabric Wear Rings, straight slot, are mainly used in hydraulics and machine building. They perform the function of guiding rods and pistons, prevent them from making metallic contact and absorb radial forces. In the material POM also available in special dimensions at short notice from routine production. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Temperature: -50 °C / +120 °C
Sliding Speed: ≤ 0,5/0,8 m/s (depends on the amterial selected)
Materials:
- Synthetic woven fabric with a specially modified phenolic resin impregnated and PTFE additives (2000K)
- Phenolic resin impregnated cotton fabric (1000K)
- Phenolic resin impregnated fine cotton fabric (0051K)
- Resin impregnated plastics fabric with PTFE additives (1030 - 0052K)
- Resin impregnated plastics fabric with graphite additives (0942 - 0052K)

Hartgewebe-Führungsringe FÜS1

Compound Fabric Wear Rings FÜS1

Compound Fabric Wear Rings with stair cut are mainly used in hydraulics and machine building. They perform the function of guiding rods in cylinders, prevent them from making metallic contact and absorb radial forces. In the material POM also available in special dimensions at short notice from routine production. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Temperature: -50 °C / +120 °C
Sliding Speed: ≤ 0,5/0,8 m/s (depends on the amterial selected)
Materials:
- Synthetic woven fabric with a specially modified phenolic resin impregnated and PTFE additives (2000K)
- Phenolic resin impregnated cotton fabric (1000K)
- Phenolic resin impregnated fine cotton fabric (0051K)
- Resin impregnated plastics fabric with PTFE additives (1030 - 0052K)
- Resin impregnated plastics fabric with graphite additives (0942 - 0052K)

Hartgewebe-Führungsringe FÜS2

Compound Fabric Wear Rings FÜS2

Compound Fabric Wear Rings with stair cut are mainly used in hydraulics and machine building. They perform the function of guiding pistons in cylinders, prevent them from making metallic contact and absorb radial forces. In the material POM also available in special dimensions at short notice from routine production. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Temperature: -50 °C / +120 °C
Sliding Speed: ≤ 0,5/0,8 m/s (depends on the amterial selected)
Materials:
- Synthetic woven fabric with a specially modified phenolic resin impregnated and PTFE additives (2000K)
- Phenolic resin impregnated cotton fabric (1000K)
- Phenolic resin impregnated fine cotton fabric (0051K)
- Resin impregnated plastics fabric with PTFE additives (1030 - 0052K)
- Resin impregnated plastics fabric with graphite additives (0942 - 0052K)

Hartgewebe-Führungsringe FÜS

Compound Fabric Wear Rings FÜS

Compound Fabric Wear Rings with stair cut are mainly used in hydraulics and machine building. They perform the function of guiding rods and pistons in cylinders, prevent them from making metallic contact and absorb radial forces. In the material POM also available in special dimensions at short notice from routine production. Other materials are available for very high or very low operating temperatures. For detailled information, please look at the specific PDF catalogue or contact our application engineers.

Application Range

Temperature: -50 °C / +120 °C
Sliding Speed: ≤ 0,5/0,8 m/s (depends on the amterial selected)
Materials:
- Synthetic woven fabric with a specially modified phenolic resin impregnated and PTFE additives (2000K)
- Phenolic resin impregnated cotton fabric (1000K)
- Phenolic resin impregnated fine cotton fabric (0051K)
- Resin impregnated plastics fabric with PTFE additives (1030 - 0052K)
- Resin impregnated plastics fabric with graphite additives (0942 - 0052K)

Führungsringe FÜ1

Guide Rings FÜ1

Guide rings FÜ1 are open piston guide rings with a mounting collar on the inside diameter and axial grooves for pressure relief. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature: -40 °C / +100 °C (max. +60 °C in water)
Sliding Speed: ≤ 5 m/s
Standard Material: polyamide (0040A)

Radialgleitlager FD1

Radial Slide Bearing FD1

Radial slide bearing of a metal composite and a sliding layer of PTFE/lead for maintenance-free operation, general applications. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature: -200 °C / +280 °C
Sliding Speed: ≤ 2 m/s
Standard Material: 0007K

Radialgleitlager FD2

Radial Slide Bearing FD2

Radial slide bearing with flange, of a metal composite and a sliding layer of PTFE/lead for maintenance-free operation, general applications. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature: -200 °C / +280 °C
Sliding Speed: ≤ 2 m/s
Standard Material: 0007K

Anlaufscheibe FDA

Thrust Washer FDA

Thrust washer of a metal composite and a sliding layer of PTFE/lead for maintenance-free operation, general applications. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature: -200 °C / +280 °C
Sliding Speed: ≤ 2 m/s
Standard Material: 0007K

Gleitband FDL

Slide Band FDL

Slide band of a metal composite and a sliding layer of PTFE/lead for maintenance-free operation, general applications. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature: -200 °C / +280 °C
Sliding Speed: ≤ 2 m/s
Standard Material: 0007K

Gleitlager FE1

Slide Bearing FE1

Slide bearing with diamond-shaped lubrication pockets, for high bearing loads and rough operation. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature: -100 °C / +200 °C
Sliding Speed: ≤ 2 m/s
Standard Material: Tin bronze

Gleitlager FE2

Slide Bearing FE2

Slide bearing with round lubrication pockets for high bearing loads and rough operation. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature: -100 °C / +200 °C
Sliding Speed: ≤ 2 m/s
Standard Material: Tin bronze

Gleitlager FE3

Slide Bearing FE3

Slide bearing without lubrication pockets, for high bearing loads. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature: -100 °C / +200 °C
Sliding Speed: ≤ 2 m/s
Standard Material: Tin bronze

Gleitlager FG1

Slide Bearing FG1

Slide bearing of a metal composit with a sliding layer of POM and round lubrication pockets. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature: -40 °C / +90 °C (temporarily to +130 °C)
Sliding Speed: ≤ 2,5 m/s
Standard Material: Metal composite and POM

Anlaufscheibe FGA

Thrust Washer FGA

Thrust washer of a metal composite and a sliding layer of POM and round lubrication pockets. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature: -40 °C / +90 °C (temporarily to +130 °C)
Sliding Speed: ≤ 2,5 m/s
Standard Material: Metal composite and POM

Radialgleitlager FE4

Radial Slide Bearing FE4

Radial slide bearing with graphite, self lucrication. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature: ≤ +250 °C
Sliding Speed: ≤ 2 m/s
Standard Material: Tin bronze, graphite

Radialgleitlager FE5

Radial Slide Bearing FE5

Radial slide bearing with flange, with graphite, self lucrication. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature: ≤ +250 °C
Sliding Speed: ≤ 2 m/s
Standard Material: Tin bronze, graphite

Gleitlager FE6

Slide Bearing FE6

Slide bearing made of sintered metal, oil impregnated. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature: -40 °C / +80 °C
Sliding Speed: ≤ 7 m/s
Standard Material: Sintered Metal

Gleitlager FE7

Slide Bearing FE7

Slide bearing made of sintered metal, oil impregnated. Other materials are available for very high or very low operating temperatures (see PDF Catalogue or contact our application engineers).

Application Range

Temperature: -40 °C / +80 °C
Sliding Speed: ≤ 7 m/s
Standard Material: Sintered Metal

Contact

Contact Do you have any questions about our products or would you like to send us a message?

Feel free to contact us! Tel: 0201 86606-0

Tel: +49(0)201 86606-0

To the contact form